Quick Find more
 

Advanced Search

View All Items
 Categories
 What's New? more
Dingdong Tone Doorbell Music Voice Module Board IC Sound Chip
Dingdong Tone Doorbell Music Voice Module Board IC Sound Chip
 8.00L.E. 
 Bestsellers
01.PHcr- Arduino 30Cm Length Wire With Headers Male From Both Ends
02.PHcr- Arduino 30Cm Wire With Headers One Side Male & One Female
03.PHcr-12 (30Cm Length Wire With Headers Female From Both Ends)
04.PHcr-13 (25Cm Length Wire With Pre-crimped Terminals at Both End
05.Connecting Jumper Wires for Bread Board & Arduino (65 Wire) 22AW
06.Arduino Board - Arduino UNO Rev3 - China Clone
07.PHcr- 20Cm Female to Male 40 Jumper Set Connecting Wire
08.PHcr- 20Cm Male to Male 40 Jumper Set Connecting Wire
09.ATMega328 "Microcontroller - bootloader UNO"
10.Battery 9V Holder With Standard DC Male Plug
 Information
Conditions of Use
Shipping & Returns
Privacy Notice
Expansion Board for Arduino UNO + GPIO for Breadboard  75.00L.E. 

Description

The Extension board is compatible with Arduino UNO R3 or other compatible board. Its purpose is to extend the IOs or ADC ports, and make it easy to connect your modules with Arduino. Also the GPIO board with cable alow you to take ports outside the arduino to your breadboard.

Usage

There are severala parts of the board should be noted.

  • The IO extension area
  • The proto field
  • The 26P jtag connector which is used to connect with the GPIO Extension Board

Details

  • The IO extension area: This is the main area of the shield. All of D0-D13 are leaded out as GND/VCC/D*/D(*+1). Many of the modules designed for Arduino need 3 or 4 wires. These port are used for them.
  • The proto field: This area is a small section that can be used to set up some proto circuit.
  • The 26P jtag connector: This connector can be used to connect with the GPIO Extension Board (included)

GPIO Board:

When use this board, we connect it with the Infiduino Extension board using the 26P wire. Then plug this board on the breadboard, so D0-D13 and A0-A5 of Infiduino/Ardudino will be leaded to the breadboard. This way will make it easy for we to set up some proto circuit on the breadboard. The following steps will be convenient. Please note the following things :

  • There are two jumpers at each side of the Jtag connector, this is used to select the 3.3V or 5V voltage that is leaded to the breadboard.
  • When plug the Extension board on the breadboard, please don't use too much strength.
Write Review
1
1
Customers who bought this product also purchased
2 x AA Battery Holder + On/Off Switch
2 x AA Battery Holder + On/Off Switch
 5.00L.E. 
More info Buy Now
Bread Board  170-Tie Point "BB-601 Yellow"
Bread Board 170-Tie Point "BB-601 Yellow"
 10.00L.E. 
More info Buy Now
Drill SUROM With Stand (up to 7000 - 16000 RPM)
Drill SUROM With Stand (up to 7000 - 16000 RPM)
 850.00L.E. 
More info Buy Now
Plastic Project Box XU-200x120 (200 (L) x 120 (W) x 70 (H) mm)
Plastic Project Box XU-200x120 (200 (L) x 120 (W) x 70 (H) mm)
 65.00L.E. 
More info Buy Now
Joystick 2Axis (Analog)-Thumb With PCB & Pin Header
Joystick 2Axis (Analog)-Thumb With PCB & Pin Header
 45.00L.E. 
More info Buy Now
5V Small Stepper Motor
5V Small Stepper Motor
 45.00L.E. 
More info Buy Now
First Product Previous Product 39 of 45 in Arduino Boards & Shields Next Product Last Product
 Shopping Cart more
0 items
 Sign in
E-mail address:

Password:

Password forgotten
Create an Account
 My Wish List more
0 items
 Tell A Friend
 
Tell someone you know about this product.
 Specials more
HDMI Splitter 1 Input x 4 Output
HDMI Splitter 1 Input x 4 Output
 395.00L.E. 350.00L.E. 
 Reviews more
Write ReviewWrite a review on this product!
 Currencies
All content and Images Copyright © 2018 RAM Electronics
Copyright © 2000 - 2018 osCmax
Powered by osCmax v2.5.4