Quick Find more
 

Advanced Search

View All Items
 Categories
 What's New? more
Heat Resistance Soldering Repair Silicone Pad 380x210mm
Heat Resistance Soldering Repair Silicone Pad 380x210mm
 200.00L.E. 
 Bestsellers
01.PHcr- Arduino 30Cm Length Wire With Headers Male From Both Ends
02.PHcr- Arduino 30Cm Wire With Headers One Side Male & One Female
03.PHcr-12 (30Cm Length Wire With Headers Female From Both Ends)
04.PHcr-13 (25Cm Length Wire With Pre-crimped Terminals at Both End
05.Arduino Board - Arduino UNO Rev3 - China Clone
06.PHcr- 20Cm Female to Male 40 Jumper Set Connecting Wire
07.Arduino Board - Arduino Nano - China Clone
08.ATmega328 (Microcontroller - bootloader UNO)
09.PHcr- 20Cm Female to Female 40 Jumper Set Connecting Wire
10.Arduino Board - Arduino Mega2560 Rev3 - China Clone
 Information
Conditions of Use
Shipping & Returns
Privacy Notice
Expansion Board for Arduino UNO + GPIO for Breadboard  75.00L.E. 

Description

The Extension board is compatible with Arduino UNO R3 or other compatible board. Its purpose is to extend the IOs or ADC ports, and make it easy to connect your modules with Arduino. Also the GPIO board with cable alow you to take ports outside the arduino to your breadboard.

Usage

There are severala parts of the board should be noted.

  • The IO extension area
  • The proto field
  • The 26P jtag connector which is used to connect with the GPIO Extension Board

Details

  • The IO extension area: This is the main area of the shield. All of D0-D13 are leaded out as GND/VCC/D*/D(*+1). Many of the modules designed for Arduino need 3 or 4 wires. These port are used for them.
  • The proto field: This area is a small section that can be used to set up some proto circuit.
  • The 26P jtag connector: This connector can be used to connect with the GPIO Extension Board (included)

GPIO Board:

When use this board, we connect it with the Infiduino Extension board using the 26P wire. Then plug this board on the breadboard, so D0-D13 and A0-A5 of Infiduino/Ardudino will be leaded to the breadboard. This way will make it easy for we to set up some proto circuit on the breadboard. The following steps will be convenient. Please note the following things :

  • There are two jumpers at each side of the Jtag connector, this is used to select the 3.3V or 5V voltage that is leaded to the breadboard.
  • When plug the Extension board on the breadboard, please don't use too much strength.
Write Review
1
1
Customers who bought this product also purchased
IDC16 male Polarized (FC16-PCB)
IDC16 male Polarized (FC16-PCB)
 2.00L.E. 
More info Buy Now
POT    5 Kohm 1/2W Vertical Square Cermet Potentiometer
POT 5 Kohm 1/2W Vertical Square Cermet Potentiometer
 3.50L.E. 
More info Buy Now
Super Glue 3gm
Super Glue 3gm
 5.00L.E. 
More info Buy Now
Grey Flat Ribbon Cable 16 pin (1 Meter Unit)
Grey Flat Ribbon Cable 16 pin (1 Meter Unit)
 5.75L.E. 
More info Buy Now
PCB  9x7 cm2 (PCB6)
PCB 9x7 cm2 (PCB6)
 5.00L.E. 
More info Buy Now
10 Kohm 8 Resistor Network (9pins)
10 Kohm 8 Resistor Network (9pins)
 1.75L.E. 
More info Buy Now
First Product Previous Product 35 of 38 in Arduino Boards & Shields Next Product Last Product
 Shopping Cart more
0 items
 Sign in
E-mail address:

Password:

Password forgotten
Create an Account
 My Wish List more
0 items
 Tell A Friend
 
Tell someone you know about this product.
 Specials more
TI LaunchPad Tiva C "TM4C1294XL" Evaluation Kit
TI LaunchPad Tiva C "TM4C1294XL" Evaluation Kit
 1,200.00L.E. 900.00L.E. 
 Reviews more
Write ReviewWrite a review on this product!
 Currencies
All content and Images Copyright © 2018 RAM Electronics
Copyright © 2000 - 2018 osCmax
Powered by osCmax v2.5.4